View HN29W12811_236874.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HN29W12811 Series
128M AND type Flash Memory More than 8,029-sector (135,657,984-bit)
ADE-203-1183C (Z) Rev. 2.0 Feb. 7, 2001 Description
The Hitachi HN29W12811 Series is a CMOS Flash Memory with AND type multi-level memory cells. It has fully automatic programming and erase capabilities with a single 3.3 V power supply. The functions are controlled by simple external commands. To fit the I/O card applications, the unit of programming and erase is as small as (2048 + 64) bytes. Initial available sectors of HN29W12811 are more than 8,029 (98% of all sector address).
Features
* On-board single power supply (VCC): VCC = 3.3 V 0.3 V * Organization AND Flash Memory: (2048 + 64) bytes x (More than 8,029 sectors) Data register: (2048 + 64) bytes * Multi-level memory cell 2 bit/per memory cell * Automatic programming Sector program time: 2.5 ms (typ) System bus free Address, data latch function Internal automatic program verify function Status data polling function * Automatic erase Single sector erase time: 1.0 ms (typ) System bus free Internal automatic erase verify function Status data polling function
HN29W12811 Series
* Erase mode Single sector erase ((2048 + 64) byte unit) * Fast serial read access time: First access time: 50 s (max) Serial access time: 60 ns (max) * Low power dissipation: ICC2 = 40 mA (max) (Read) ISB2 = 50 A (max) (Standby) ICC3/ICC4 = 40 mA (max) (Erase/Program) ISB3 = 5 A (max) (Deep standby) * The following architecture is required for data reliability. Error correction: more than 1-bit error correction per each sector read Spare sectors: 1.8% (145 sectors) within usable sectors
Ordering Information
Type No. HN29W12811T-60 Available sector More than 8,029 sectors Package 12.0 x 18.40 mm 2 0.5 mm pitch 48-pin plastic TSOP I (TFP-48DA)
2
HN29W12811 Series
Pin Arrangement
48-pin TSOP VCC VSS VSS VSS VSS RES RDY/Busy SC OE I/O0 I/O1 I/O2 I/O3 VCC VSS I/O4 I/O5 I/O6 I/O7 CDE WE CE VSS VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 (Top view) 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC
Pin Description
Pin name I/O0 to I/O7 CE OE WE CDE VCC* VSS *
1 1
Function Input/output Chip enable Output enable Write enable Command data enable Power supply Ground Ready/Busy Reset Serial clock
RDY/Busy RES SC Note:
1. All V CC and VSS pins should be connected to a common power supply and a ground, respectively.
3
HN29W12811 Series
Block Diagram
2048 + 64
Sector address buffer
X-decoder
8192 x (2048 + 64) x 8 memory matrix
** I/O0 to I/O7 Data input buffer Input data control
Data register (2048 + 64)
* *
* Multiplexer *
* *
* *
Y-gating Y-decoder
Data output buffer ***
RDY/Busy
** * * Y-address counter
VCC VSS
CE OE WE SC RES CDE Control signal buffer Read/Program/Erase control
4
8029 - 8192
HN29W12811 Series
Memory Map and Address
Sector address 2048 bytes 1FFFH 1FFEH 1FFDH 2048 bytes 2048 bytes 64 bytes 64 bytes 64 bytes
2048 bytes 0002H 0001H 0000H 000H 2048 + 64 bytes 2048 bytes 2048 bytes
64 bytes 64 bytes 64 bytes 800H 83FH Column address
Control bytes Cycles SA (1): SA (2): Column address CA (1): CA (2): Address Sector address I/O0 I/O1 I/O2 I/O3 A0 A1 A2 A3 A8 A9 A10 A11 A0 A1 A2 A3 A8 A9 A10 A11 I/O4 I/O5 I/O6 I/O7 A4 A5 A6 A7 A12 x*2 x x A4 A5 A6 A7 x x x x
First cycle Second cycle First cycle Second cycle
Notes: 1. Some failed sectors may exist in the device. The failed sectors can be recognized by reading the sector valid data written in a part of the column address 800 to 83F (The specific address is TBD.). The sector valid data must be read and kept outside of the sector before the sector erase. When the sector is programmed, the sector valid data should be written back to the sector. 2. An x means "Don't care". The pin level can be set to either VIL or VIH, referred to DC characteristics.
8029 - 8192 sectors *1
5
HN29W12811 Series
Pin Function
CE: CE is used to select the device. The status returns to the standby at the rising edge of CE in the reading operation. However, the status does not return to the standby at the rising edge of CE in the busy state in programming and erase operation. OE: Memory data and status register data can be read, when OE is VIL . WE: Commands and address are latched at the rising edge of WE. SC: Programming and reading data is latched at the rising edge of SC. RES: RES pin must be kept at the VILR (V SS 0.2 V) level when VCC is turned on and off. In this way, data in the memory is protected against unintentional erase and programming. RES must be kept at the VIHR (VCC 0.2 V) level during any operations such as programming, erase and read. CDE: Commands and data are latched when CDE is VIL and address is latched when CDE is VIH. RDY/Busy: The RDY/Busy indicates the program/erase status of the flash memory. The RDY/Busy signal is initially at a high impedance state. It turns to a VO L level after the (40H) command in programming operation or the (B0H) command in erase operation. After the erase or programming operation finishes, the RDY/Busy signal turns back to the high impedance state. I/O0 to I/O7: The I/O pins are used to input data, address and command, and are used to output memory data and status register data.
Mode Selection
Mode Deep standby Standby Output disable Status register read* Command write*
2 1
CE x* 4 VIH VIL VIL VIL
OE x x VIH VIL VIH
WE x x VIH VIH VIL
SC x x x x VIL
RES VILR VIHR VIHR VIHR VIHR
CDE x x x x VIL
RDY/Busy* 3 I/O0 to I/O7 VOH VOH VOH VOH VOH High-Z High-Z High-Z Status register outputs Din
Notes: 1. Default mode after the power on is the status register read mode (refer to status transition). From I/O0 to I/O7 pins output the status, when CE = VIL and OE = VIL (conventional read operation condition). 2. Refer to the command definition. Data can be read, programmed and erased after commands are written in this mode. 3. The RDY/Busy bus should be pulled up to VCC to maintain the VOH level while the RDY/Busy pin outputs a high impedance. 4. An x means "Don't care". The pin level can be set to either VIL or VIH referred to DC characteristics.
6
HN29W12811 Series
Command Definition*1, 2
First bus cycle Command Read Bus cycles Serial read (1) (Without CA) 3 (With CA) Serial read (2) Read identifier codes Data recovery read Auto erase Single sector (Without CA*7) (With CA*7) Program (2)*10 Operation Data in mode*3 Write 00H 00H F0H 90H 01H 20H 10H 10H 1FH 0FH 11H 11H FFH 50H 12H Write SA (1)*4 Second bus cycle Operation Data in mode Write Write Write Read Read Write Write Write Write Write Write Write SA (1)*4 SA (1)*4 SA (1)*4 SA (1)*4 SA (1)*4 SA (1)*4 SA (1)*4 SA (1)*4 SA (1)*4 SA (1)*4 ID*8, 9 Recovery data Data out
3 + 2h*6 Write 3 1 1 4 4 Write Write Write Write Write
Auto program Program (1)
4 + 2h*6 Write 4 Write Write Write
Program (3) (Control bytes)*7 4 Program (4) (WithoutCA*7) 4 (With CA*7) Reset Clear status register Data recovery write
4 + 2h*6 Write 1 1 4 Write Write Write
7
HN29W12811 Series
Third bus cycle Command Read Bus cycles Serial read (1) (Without CA) 3 (With CA) Serial read (2) Read identifier codes Data recovery read Auto erase Single sector (Without CA*7) (With CA*7) Program (2)*
10
Fourth bus cycle Operation mode Data in
Operation mode Write
Data in SA (2)*4 SA (2)*4 SA (2)*4
3 + 2h*6 Write 3 1 1 4 4 Write Write Write
Write
CA (1)*5
SA (2)*4 SA (2)*4 SA (2)*4 SA (2)*
4
Write Write Write Write Write Write Write
B0H*11 40H *11, 12 CA (1) 40H *11, 12 40H *11, 12 40H *11, 12 CA (1)
Auto program Program (1)
4 + 2h*6 Write 4 Write Write Write
Program (3) (Control bytes)*7 4 Program (4) (WithoutCA*7) 4 (With CA*7) Reset Clear status register Data recovery write
SA (2)*4 SA (2)*4 SA (2)*4
4 + 2h*6 Write 1 1 4 Write
SA (2)*4
Write
40H *11, 12
8
HN29W12811 Series
Fifth bus cycle Command Read Bus cycles Serial read (1) (Without CA) 3 (With CA) Serial read (2) Read identifier codes Data recovery read Auto erase Single sector (Without CA*7) (With CA*7) Program (2)*10
7
Sixth bus cycle Operation mode Data in
Operation mode
Data in
3 + 2h*6 Write 3 1 1 4 4 4 + 2h*6 Write 4
CA (2)*5
Auto program Program (1)
CA (2)*5
Write
40H *11, 12
Program (3) (Control bytes)* 4 Program (4) (WithoutCA*7) 4 (With CA*7) Reset Clear status register Data recovery write 4 + 2h*6 Write 1 1 4 CA (2) Write 40H *11, 12
Notes: 1. Commands and sector address are latched at rising edge of WE pulses. Program data is latched at rising edge of SC pulses. 2. The chip is in the read status register mode when RES is set to VIHR first time after the power up. 3. Refer to the command read and write mode in mode selection. 4. SA (1) = Sector address (A0 to A7), SA (2) = Sector address (A8 to A12). 5. CA (1) = Column address (A0 to A7), CA (2) = Column address (A8 to A11). (0 A11 to A0 83FH) 6. The variable h is the input number of times of set of CA (1) and CA (2) (1 h 2048 + 64). Set of CA (1) and CA (2) can be input without limitation. 7. By using program (1) and (3), data can additionally be programmed maximum 15 times for each sector before erase. 8. ID = Identifier code; Manufacturer code (07H), Device code (95H). 9. The manufacturer identifier code is output when CDE is low and the device identifier code is output when CDE is high. 10. Before program (2) operations, data in the programmed sector must be erased. 11. No commands can be written during auto program and erase (when the RDY/Busy pin outputs a VOL ). 12. The fourth or sixth cycle of the auto program comes after the program data input is complete.
9
HN29W12811 Series
Mode Description
Read Serial Read (1): Memory data D0 to D2111 in the sector of address SA is sequentially read. Output data is not valid after the number of the SC pulse exceeds 2112. When CA is input, memory data D (m) to D (m + j) in the sector of address SA is sequentially read. Then output data is not valid after the number of the SC pulse exceeds (2112 to m). The mode turns back to the standby mode at any time when CE is VIH. Serial Read (2): Memory data D2048 to D2111 in the sector of address SA is sequentially read. Output data is not valid after the number of the SC pulse exceeds 64. The mode turns back to the standby mode at any time when CE is VIH. Automatic Erase Single Sector Erase: Memory data D0 to D2111 in the sector of address SA is erased automatically by internal control circuits. After the sector erase starts, the erasure completion can be checked through the RDY/Busy signal and status data polling. All the bits in the sector are "1" after the erase. The sector valid data stored in a part of memory data D2048 to D2111 must be read and kept outside of the sector before the sector erase. Automatic Program Program (1): Program data PD0 to PD2111 is programmed into the sector of address SA automatically by internal control circuits. When CA is input, program data PD (m) to PD (m + j) is programmed from CA into the sector of address SA automatically by internal control circuits. By using program (1), data can additionally be programed for each sector before the following erase. When the column is programmed, the data of the column must be [FF]. After the programming starts, the program completion can be checked through the RDY/Busy signal and status data polling. Programmed bits in the sector turn from "1" to "0" when they are programmed. The sector valid data should be included in the program data PD2048 to PD2111. Program (2): Program data PD0 to PD2111 is programmed into the sector of address SA automatically by internal control circuits. After the programming starts, the program completion can be checked through the RDY/Busy signal and status data polling. Programmed bits in the sector turn from "1" to "0" when they are programmed. The sector must be erased before programming. The sector valid data should be included in the program data PD2048 to PD2111. Program (3): Program data PD2048 to PD2111 is programmed into the sector of address SA automatically by internal control circuits. By using program (3), data can additionally be programed for each sector befor the following erase. When the column is programmed, the data of the column must be [FF]. After the programming starts, the program completion can be checked through the RDY/Busy signal and status data polling. Programmed bits in the sector turn from "1" to "0" when they are programmed.
10
HN29W12811 Series
Program (4): Program data PD0 to PD2111 is programmed into the sector of address SA automatically by internal control circuits. When CA is input, program data PD (m) to PD (m + j) is programmed from CA into the sector of address SA automatically by internal control circuits. By using program (4), data can be rewritten for each sector before the following erase. So the column data before programming operation are either "1" or "0". In this mode, E/W number of times must be counted whenever program (4) execute. After the programming starts, the program completion can be checked through the RDY/Busy signal and status data polling. The sector valid data should be included in the program data PD2048 to PD2111.
8191 Sector address Memory array 0 0 8191 Sector address Memory array 0 8191 Sector address Memory array
0 Register
2111
0
Column address Register
2111
0
2048 Register Serial read (2) Program (3)
2111
Serial read (1) (Without CA) Program (1) (Without CA) Program (2)
Serial read (1) (With CA) Program (1) (With CA)
Status Register Read The status returns to the status register read mode from standby mode, when CE and OE is VIL. In the status register read mode, I/O pins output the same operation status as in the status data polling defined in the function description. Identifier Read The manufacturer and device identifier code can be read in the identifier read mode. The manufacturer and device identifier code is selected with CDE VIL and V IH, respectively.
11
HN29W12811 Series
Data Recovery Read When the programming was an error, the program data can be read by using data recovery read. When an additional programming was an error, the data compounded of the program data and the origin data in the sector address SA can be read. Output data are not valid after the number of SA pulse exeeds 2112. The mode turns back to the standby mode at any time when CE is VIH. The read data are invalid when addresses are latched at a rising edge of WE pulse after the data recovery read command is written. Data Recovery Write When the programming into a sector of address SA was an error, the program data can be rewritten automatically by internal control circuit into the other selected sector of address SA'. In this case, top address [SA12] of sector of address SA' must be the same as SA. Since the data recovery write mode is internally Program (4) mode, rewritten sector of address SA' needs no sector erase before rewrite. After the data recovery write mode starts, the program completion can be checked through the RDY/Busy signal and the status data polling.
12
HN29W12811 Series
Command/Address/Data Input Sequence
Serial Read (1) (With CA before SC)
Command /Address CDE WE SC Low Data output Data output
00H
SA (1)
SA (2)
CA (1)
CA (2)
CA (1)'
CA (2)'
Serial Read (1) (With CA after SC)
Command /Address CDE WE SC Low Data output Data output Data output
00H
SA (1)
SA (2)
CA (1)
CA (2)
CA (1)'
CA (2)'
Serial Read (1) (Without CA), (2)
Command/Address CDE WE SC Low Data output
00H/F0H
SA (1)
SA (2)
Single Sector Erase
Command/Address CDE WE SC Low Erase start
20H
SA (1)
SA (2)
B0H
13
HN29W12811 Series
Program (1), (4) (With CA before SC)
Command /Address CDE WE SC Low Data input Data input Program start
10H/11H
SA (1)
SA (2)
CA (1)
CA (2)
CA (1)'
CA (2)'
40H
Program (1), (4) (With CA after SC)
Command /Address CDE WE SC Low Data input Data input Data input Program start
10H/11H
SA (1)
SA (2)
CA (1)
CA (2)
CA (1)'
CA (2)'
40H
Program (1), (4) (Without CA)
Command/Address CDE WE SC Low Data input Program start
10H/11H
SA (1)
SA (2)
40H
Program (2)
Command/Address CDE WE SC Low Data input Program start
1FH
SA (1)
SA (2)
40H
14
HN29W12811 Series
Program (3)
Command/Address CDE WE SC Low Data input Program start
0FH
SA (1)
SA (2)
40H
ID Read Mode
Command/Address CDE WE SC Low Manufacture Device code Manufacture code output output code output
90H
Data Recovery Read Mode
Command/Address CDE WE SC Low Data output
01H
Data Recovery Write Mode
Command/Address CDE WE SC Low Program start
12H
SA (1)
SA (2)
40H
15
HN29W12811 Series
Status Transition
Deep standby RES 00H/F0H FFH CE 90H FFH CE 20H FFH Sector Erase setup SA (1), SA (2) Sector address input B0H Erase start OE Read (1) / (2) SA (1), SA (2) setup VCC Column address input CA(1) CA(2) Sector address OE, SC input
Power off
CA(1)' OE CA(2)' SC
Read (1) / (2)
ID read setup
CDE, OE
ID read
BUSY Status register read
Erase finish Column address SC, CDE PD(m) input CA(1) CA(2)
CA(1)' to CA(2)' PD(m+j)
CE Standby
PD0 to 10H SA (1), PD2111 OE 40H Output /11H SA (2) Sector address Program Program Program disable (1)/(4) setup input data input start FFH SC, CDE Program finish
Status register read
PD0 to 1FH SA (1), PD2111*3 OE 40H /0FH Program (2)/(3) SA (2) Sector address Status register Program Program read input data input setup start SC, CDE FFH Program finish Program error or Status register clear 50H Erase error
CE*2 FFH*2 ERROR Data recovery OE, SC Data recovery read setup read SA(1) 1 Error CE Output 12H* Data recovery SA(2) Sector address 40H standby disable write setup input *4 FFH OE Status register read OE Status register read 01H*1
Notes: 1. 2. 3. 4.
(01H)/(12H) Data recovery read/write can be used only for Program (1), (2), (3), (4) errors. When reset is done by CE or FFH, error status flag is cleared. When Program (3) mode, input data is PD2048 to PD2111. When Error standby, ICC3 level is current.
16
HN29W12811 Series
Absolute Maximum Ratings
Parameter VCC voltage VSS voltage All input and output voltages Operating temperature range Storage temperature range Storage temperature under bias Symbol VCC VSS Vin, Vout Topr Tstg Tbias Value -0.6 to +4.6 0 -0.6 to VCC + 0.3 0 to +70 -65 to +125 -10 to +80 Unit V V V C C C 3 1, 2 Notes 1
Notes: 1. Relative to VSS . 2. Vin, Vout = -2.0 V for pulse width 20 ns. 3. Device storage temperature range before programming.
Capacitance (Ta = 25C, f = 1 MHz)
Parameter Input capacitance Output capacitance Symbol Cin Cout Min -- -- Typ -- -- Max 6 12 Unit pF pF Test conditions Vin = 0 V Vout = 0 V
17
HN29W12811 Series
DC Characteristics (VCC = 3.3 V 0.3 V, Ta = 0 to +70C)
Parameter Input leakage current Output leakage current Standby V CC current Symbol Min I LI I LO I SB1 I SB2 Deep standby VCC current Operating VCC current I SB3 I CC1 I CC2 Operating VCC current (Program) I CC3 Operating VCC current (Erase) Input voltage I CC4 VIL VIH Input voltage (RES pin) VILR VIHR Output voltage VOL VOH -- -- -- -- -- -- -- -- -- -0.3* 2.0 -0.2
1, 2
Typ -- -- 0.3 30 1 5 20 20 20 -- -- --
Max 2 2 1 50 5 20 40 40 40 0.8 VCC + 0.3* 0.2 VCC + 0.2 0.4 --
3
Unit A A mA A A mA mA mA mA V V V V V V
Test conditions Vin = VSS to V CC Vout = VSS to V CC CE = VIH CE = VCC 0.2 V, RES = VCC 0.2 V RES = VSS 0.2 V Iout = 0 mA, f = 0.2 MHz Iout = 0 mA, f = 20 MHz In programming In erase
VCC - 0.2 -- -- 2.4 -- --
I OL = 2 mA I OH = -2 mA
Notes: 1. VIL min = -1.0 V for pulse width 50 ns in the read operation. VIL min = -2.0 V for pulse width 20 ns in the read operation. 2. VIL min = -0.6 V for pulse width 20 ns in the erase/data programming operation. 3. VIH max = VCC + 1.5 V for pulse width 20 ns. If VIH is over the specified maximum value, the operations are not guaranteed.
AC Characteristics (VCC = 3.3 V 0.3 V, Ta = 0 to +70C)
Test Conditions * * * * * Input pulse levels: 0.4 V/2.4 V Input pulse levels for RES: 0.2 V/VCC - 0.2 V Input rise and fall time: 5 ns Output load: 1 TTL gate + 100 pF (Including scope and jig.) Reference levels for measuring timing: 0.8 V, 1.8 V
18
HN29W12811 Series
Power on and off, Serial Read Mode
HN29W12811 -60 Parameter Write cycle time Serial clock cycle time CE setup time CE hold time Write pulse time Write pulse high time Address setup time Address hold time Data setup time Data hold time SC to output delay OE setup time for SC OE low to output low-Z OE setup time before read OE setup time before command write SC to output hold OE high to output float WE to SC delay time RES to CE setup time SC to OE hold time SC pulse width SC pulse low time SC setup time for CE CDE setup time for WE CDE hold time for WE VCC setup time for RES RES to V CC hold time CE setup time for RES RDY/Busy undefined for V CC off Symbol t CWC t SCC t CES t CEH t WP t WPH t AS t AH t DS t DH t SAC t OES t OEL t OER t OEWS t SH t DF t WSD t RP t SOH t SP t SPL t SCS t CDS t CDH t VRS t VRH t CESR t DFP Min 120 60 0 0 60 40 50 10 50 10 -- 0 0 250 0 15 -- 50 1 50 25 25 0 0 20 1 1 1 0 Typ -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Max -- -- -- -- -- -- -- -- -- -- 60 -- 40 -- -- -- 40 -- -- -- -- -- -- -- -- -- -- -- -- Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns s ms ns ns ns ns ns ns s s s ns CE = VIH CE = VIH CE = OE = VIL, WE = VIH CE = VIL, WE = VIH 1 2 CE = OE = VIL, WE = VIH CE = VIL, OE = VIH Test conditions Notes
19
HN29W12811 Series
HN29W12811 -60 Parameter RES high to device ready CE pulse high time CE, WE setup time for RES RES to CE, WE hold time SC setup for WE CE hold time for OE SA (2) to CA (2) delay time RDY/Busy setup for SC Symbol t BSY t CPH t CWRS t CWRH t SW t COH t SCD t RS Min -- 200 0 0 50 0 -- 200 -- -- Typ -- -- -- -- -- -- -- -- -- 45 Max 1 -- -- -- -- -- 30 -- 1 -- Unit ms ns ns ns ns ns s ns s s Test conditions Notes
Time to device busy on read mode t DBR Busy time on reset mode t RBSY
Notes: 1. t DF is a time after which the I/O pins become open. 2. t WSD (min) is specified as a reference point only for SC, if t WSD is greater than the specified tWSD (min) limit, then access time is controlled exclusively by tSAC.
20
HN29W12811 Series
Program, Erase and Erase Verify
HN29W12811 -60 Parameter Write cycle time Serial clock cycle time CE setup time CE hold time Write pulse time Write pulse high time Address setup time Address hold time Data setup time Data hold time OE setup time before command write Symbol t CWC t SCC t CES t CEH t WP t WPH t AS t AH t DS t DH t OEWS Min 120 60 0 0 60 40 50 10 50 10 0 40 250 -- -- -- -- -- -- 50 2 200 25 25 0 35 50 Typ -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 1.0 2.5 2.0 2.5 -- -- -- -- -- -- -- -- Max -- -- -- -- -- -- -- -- -- -- -- -- -- 150 1 14.0 22.0 22.0 30.0 -- -- -- -- -- -- -- -- Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns s ms ms ms ms s s ns ns ns ns ns ns CDE = VIL Test conditions Note
OE setup time before status polling t OEPS OE setup time before read Time to device busy t OER t DB
Time to device busy on read mode t DBR Auto erase time Auto program time Program(1), (3) Program(2) Program(4), Data recovery write WE to SC delay time WE to SC delay time on recovery read mode CE pulse high time SC pulse width SC pulse low time Data setup time for SC Data hold time for SC SC setup for WE t ASE t ASP t ASP t ASP t WSD t WSDR t CPH t SP t SPL t SDS t SDH t SW
21
HN29W12811 Series
HN29W12811 -60 Parameter SC setup for CE SC hold time for WE CE to output delay OE to output delay OE high to output float RES to CE setup time CDE setup time for WE CDE hold time for WE CDE setup time for SC CDE hold time for SC Next cycle ready time CDE to OE hold time CDE to output delay CDE to output invalid CE setup time for OE CE hold time for OE CDE to OE setup time OE setup time for SC OE low to output low-Z SC to output delay SC to output hold RDY/Busy setup for SC CE hold time for WE CE hold time for WE on recovery read mode WE hold time for WE Busy time on read mode Note: Symbol t SCS t SCHW t CE t OE t DF t RP t CDS t CDH t CDSS t CDSH t RDY t CDOH t CDAC t CDF t COS t COH t CDOS t OES t OEL t SAC t SH t RS t CWH t CWHR t WWH t RBSY Min 0 20 -- -- -- 1 0 20 1.5 30 0 50 -- -- 0 0 20 0 0 -- 15 200 1.0 2 1 -- Typ -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 45 Max -- -- 120 60 40 -- -- -- -- -- -- -- 50 100 -- -- -- -- 40 60 -- -- -- -- -- -- Unit ns ns ns ns ns ms ns ns s ns ns ns ns ns ns ns ns ns ns ns ns ns s s s s 1 Test conditions Note
1. t DF is a time after which the I/O pins become open.
22
HN29W12811 Series
Timing Waveforms
Power on and off Sequence
VCC
tVRS
CE tRP WE tCWRS RES *1 tBSY RDY /Busy Notes: 1. RES must be kept at the VILR level referred to DC characteristics at the rising and falling edges of VCC to guarantee data stored in the chip. 2. RES must be kept at the VIHR level referred to DC characteristics while I/O7 outputs the VOL level in the status data polling and RDY/Busy outputs the VOL level. 3. : Undefined *2 High-Z Ready tBSY tCES tCEH tCESR tRP tCES tCEH tCESR tCWRH tVRH *1 tDFP
23
HN29W12811 Series
Serial Read (1) (2) Timing Waveform
*1 tCPH tCWC tWPH tOER *3
CE tCES OE tOEWS WE tCDS CDE tWP tCDS tCDH SC tSCS I/O0 to I/O7 00H /F0H RES tRP RDY /Busy tDBR SA(1) SA(2) tDS tDH tAS tAH tAS tAH tOEL tWP tWP tOES tWSD tSCC tSP tSCC *2 tCWC tWPH
tCOH
tCEH
tWP tCDH
tSOH
tCDS tDS tDH
tSPL tSAC tSH
tSAC tSH
D1out/D2049out
tSAC
tSAC
tDF
D0out/D2048out
D2111out/D2111out
*2
FFH
tRBSY tRS High-Z
Notes: 1. The status returns to the standby at the rising edge of CE. 2. Output data is not valid after the number of the SC pulse exceeds 2112 and 64 in the serial read mode (1)and (2), respectively. 3. After any commands are written, the status can return to the standby after the command FFH is input and CE turns to the VIH level.
Serial Read (1) with CA before SC Timing Waveform
h-1 cycle *
5
CE tCES OE tOEWS WE tCDS CDE tCDH SC tSCS I/O0 to I/O7 tRP RES tDBR RDY /Busy tRBSY tRS High-Z 00H SA(1) SA(2) CA(1) CA(2)
D(n)out D(n+1)out D(n+i)out *2
* tCOH 1 tCPH tCWC tWPH tCWC tWPH tCWC tWPH tOEWS tOER tSW tWP tWP tSCD tWSD tWP tOES tSCC tSP tDS tDH tAS tAH tAS tAH tAS tAH tAS tAH tSAC tSPL tSAC t tOEL SAC t tSH SH tSAC tDF tAS tAH tAS tAH CA(2)' tSAC tOEL tSP tSPL tSAC tSAC tSH tSH D(m)out D(m+1)out tSAC tDF tDS tDH tSCC *2 tSOH tCWC tWPH tOER * tCEH4
tCWC tWPH
tWP
tCDS t WP
tWP
tWP tOES tSCC tSCC *3 tSOH
tWP tCDH
tCDS
CA(1)'
D(m+j)out *3
FFH
Notes: 1. 2. 3. 4.
The status returns to the Standby at the rising edge of CE. Output data is not valid after the number of the SC pulse exceeds (2112-n). (i 2111-n, 0 n 2111) Output data is not valid after the number of the SC pulse exceeds (2112-m). (j 2111-m, 0 m 2111) After any commands are written, the status can return to the standby after the command FFH is input and CE turns to the VIH level. 5. This interval can be repeated (h-1) cycle. (1 h 2048 + 64)
24
HN29W12811 Series
Serial Read (1) with CA after SC Timing Waveform
5 h cycle*
tCOH *1
CE tCES OE tOEWS WE tWP CDE tCDH tCDS SC tSCS I/O0 to I/O7 tRP RES tDBR RDY /Busy tRBSY tRS High-Z 00H SA(1) SA(2)
D0out D1out D(k)out *2
tCPH tCWC tWPH tOER tSW tWP tWP tOES tCDS tWSD tSCC tSCC 2 * tSOH tOEWS tCWC tWPH tOER
4 tCEH*
tCWC tWPH
tWP
tWP tOES tSCC tSCC *3 tSOH
tWP tCDH
tCDS
tDS tDH
tAS tAH
tAS tAH
t t tOEL t SP SPL tSH SAC
tSAC
tSAC tSH
tSAC
tDF
tSP tAS tAH tAS tAH tOEL CA(1) CA(2) tSAC tSPL tSAC tSH D(m)out tSH D(m+1)out D(m+j)out *3 tSAC tSAC tDF tDS tDH
FFH
Notes: 1. 2. 3. 4. 5.
The status returns to the Standby at the rising edge of CE. Output data is not valid after the number of the SC pulse exceeds 2112. (0 k 2111) Output data is not valid after the number of the SC pulse exceeds (2112-m). (j 2111-m, 0 m 2111) After any commands are written, the status can return to the standby after the command FFH is input and CE turns to the VIH level. This interval can be repeated h cycle. (1 h 2048 + 64)
Erase and Status Data Polling Timing Waveform (Sector Erase)
CE tCES OE tOEWS WE tCDS CDE tWP tCDS tCDH SC tSCS I/O0 to I/O7 20H RES tRP RDY /Busy High-Z tDB *1 *2 High-Z SA(1) SA(2) B0H IO7 = VOL IO7 = VOH tDS tDH tAS tAH tAS tAH tDS tDH tDF tDF tWP tWP tWP tCDS tCDH tCDH tSCHW tCWC tWPH tCWC tWPH tCWC tWPH tCEH tOEPS tCE tOE tASE tRDY tCDS
Notes: 1. Any commands,including reset command FFH, cannot be input while RDY/Busy outputs a VOL. 2. The status returns to the standby status after RDY/Busy returns to High-Z.
25
HN29W12811 Series
Program (1) and Status Data Polling Timing Waveform
CE tCES OE tOEWS tCWC tWPH WE tCDS CDE tCDH SC tSCS I/O0 to I/O7 10H RES tRP RDY /Busy High-Z *2 SA (1) SA (2) PD0 PD1 PD2111 40H tDB I/O7 = VOL I/O7 = VOH *3 High-Z tDS tDH tAS tAH tAS tAH tSDH tSP tSDS tSP tDS tDH tDF tDF tCDH tSCC tSPL *1 tCDH tSCHW tWPtCDS tWP tWP tCDSS tSW tWP tASP tCWC tWPH tOEPS tOE tRDY tCEH tCE
tCDS
Notes: 1. 2. 3. 4.
The programming operation is not guranteed when the number of the SC pulse exceeds 2112. Any commands, including reset command FFH, cannot be input while RDY/Busy is VOL. The status returns to the standby status after RDY/Busy returns to High-Z. By using program (1), data can be programmed additionally for each sector before erase.
26
HN29W12811 Series
Program (1) with CA before SC and Status Data Polling Timing Waveform
h-1 cycle*6 CE tCES OE tOEWS tCWC tCWC tWPH tWPH tCWC tWPH tCWC tWPH tSW tCDS t CDE tSCS SC tDS I/O0 to I/O7 10H RES tRP RDY /Busy Notes: 1. 2. 3. 4. 5. 6. High-Z tDB *3 The programming operation is not guaranteed when the number of the SC pulse exceeds (2112 - n).(i 2111 - n, 0 n 2111) The programming operation is not guaranteed when the number of the SC pulse exceeds (2112 - m).(j 2111 - m, 0 m 2111) Any commands, including reset command FFH, cannot be input while RDY/Busy is VOL. The status returns to the standby status after RDY/Busy returns to High-Z. By using program (1), data can be programmed additionally for each sector before erase. This interval can be repeated (h - 1) cycle.(1 h 2048 + 64) High-Z*4 SA(1) SA(2) CA(1) CA(2) PD(n) PD(n+1) PD(n+i)*1 CA(1)' CA(2)' PD(m) PD(m+1)PD(m+j)*2 40H I/O7=VOL I/O7=VOH t tDHAS tAH tAS tAH tAS tAH tAS tCDH tCDH tSCC tSPL tSP *1 tSP tCDSH tAH tCDH tAH tSDS tSCC tSPL tSDH *2 tSP tSP tDS t WP CDS tWP tWP tWP tWP tCDSS tCDS tWP tWP tCDSS tWP tSW tCDH tSCHW tDH tDF tDF tASP tCDS tCWC tWPH tCEH tCE
tOEPS
tOE
tRDY
WE
tAH t tSDS SDH
tAS
tAS
Program (1) with CA after SC and Status Data Polling Timing Waveform
h cycle*6 CE tCES OE tOEWS tCWC tCWC tWPH tWPH tSW tCDS tWP tCDS tWP CDE tSCS SC tDS I/O0 to I/O7 10H RES tRP RDY /Busy Notes: 1. 2. 3. 4. 5. 6. High-Z tDB *3 The programming operation is not guaranteed when the number of the SC pulse exceeds 2112.(0 k 2111) The programming operation is not guaranteed when the number of the SC pulse exceeds (2112 - m).(j 2111 - m, 0 m 2111) Any commands, including reset command FFH, cannot be input while RDY/Busy is VOL. The status returns to the standby status after RDY/Busy returns to High-Z. By using program (1), data can be programmed additionally for each sector before erase. This interval can be repeated h cycle.(1 h 2048 + 64) High-Z*4 SA(1) SA(2) PD0 PD1 PD(k)*1 CA(1) CA(2) PD(m) PD(m+1)PD(m+j)*2 40H I/O7=VOL I/O7=VOH t tDHAS tAH tAS tAH tSDS tCDH tCDH tSCC tSPL tSDH tSP *1 tSP tCDSH tAH tCDH tAH tSCC tSPL tSDH *2 tSP tSP tWP tCDSS tCDS tWP tWP tCDSS tWP tSW tCDH tSCHW tDH tDF tDF tASP tCDS tCWC tWPH tCEH tCE
tOEPS
tOE
tRDY
WE
tAS
tAS
tSDS
tDS
27
HN29W12811 Series
Program (2) and Status Data Polling Timing Waveform
CE tCES OE tOEWS tCWC tCWC tWPH tWPH tCEH tOEPS tCE tRDY
tOE tASP
WE tCDS CDE tCDH SC tSCS I/O0 to I/O7 1FH RES tRP RDY /Busy High-Z *2 SA (1) SA (2) PD0 PD1 PD2111 40H tDB I/O7 = VOL I/O7 = VOH *3 High-Z tDS tDH tAS tAH tAS tAH tSDH tSP tSDS tSP tDS tDH tDF tDF tCDH tSCC tSPL *1 tCDH tSCHW tWPtCDS tWP tWP tCDSS tSW tWP tCDS
Notes: 1. 2. 3. 4.
The programming operation is not guranteed when the number of the SC pulse exceeds 2112. Any commands, including reset command FFH, cannot be input while RDY/Busy is VOL. The status returns to the standby status after RDY/Busy returns to High-Z. By using program (2), the programmed data of each sector must be erased before programming next data.
28
HN29W12811 Series
Program (3) and Status Data Polling Timing Waveform
CE tCES OE tOEWS tCWC tWPH WE tCDS CDE tCDH SC tSCS I/O0 to I/O7 0FH RES tRP RDY /Busy High-Z *2 SA (1) SA (2) PD2048 PD2049 PD2111 40H tDB I/O7 = VOL I/O7 = VOH *3 High-Z tDS tDH tAS tAH tAS tAH tSDH tSP tSDS tSP tDS tDH tDF tDF tCDH tSCC tSPL *1 tCDH tSCHW tWPtCDS tWP tWP tCDSS tSW tWP tASP tCDS tCWC tOEPS tOE tRDY tCEH tCE
Notes: 1. 2. 3. 4.
The programming operation is not guranteed when the number of the SC pulse exceeds 64. Any commands, including reset command FFH, cannot be input while RDY/Busy is VOL. The status returns to the standby status after RDY/Busy returns to High-Z. By using program (3), the data can be programmed additionally for each sector before erase.
29
HN29W12811 Series
Program (4) and Status Data Polling Timing Waveform
CE tCES OE tOEWS tCWC tWPH WE tCDS CDE tCDH SC tSCS I/O0 to I/O7 11H RES tDBR tRP RDY /Busy tRBSY Notes: 1. 2. 3. 4. The programming operation is not guranteed when the number of the SC pulse exceeds 2112. Any commands, including reset command FFH, cannot be input while RDY/Busy is VOL. The status returns to the standby status after RDY/Busy returns to High-Z. By using program (4), data can be rewritten for each sector. tRS High-Z *2 SA (1) SA (2) PD0 PD1 PD2111 40H tDB I/O7 = VOL I/O7 = VOH *3 High-Z tDS tDH tAS tAS tAH tCDH tWSD tAH tSDH tSP tSDS tSP tDS tDH tDF tDF tSCC tSPL *1 tCDH tSCHW tWPtCDS tWP tWP tCDSS tSW tWP tASP tCDS tCWC tWPH tOEPS tOE tRDY tCEH tCE
30
HN29W12811 Series
Program (4) with CA before SC and Status Data Polling Timing Waveform
h-1 cycle*6 CE tCES OE tOEWS tCWC tCWC tWPH tWPH tCWC tWPH tCWC tWPH tSW tCDS tWP tCDS tWP CDE tSCS SC tDS I/O0 to I/O7 11H RES tRP RDY /Busy Notes: 1. 2. 3. 4. 5. 6. tDBR tRBSY tRS High-Z tDB *3 The programming operation is not guaranteed when the number of the SC pulse exceeds (2112 - n).(i 2111 - n, 0 n 2111) The programming operation is not guaranteed when the number of the SC pulse exceeds (2112 - m).(j 2111 - m, 0 m 2111) Any commands, including reset command FFH, cannot be input while RDY/Busy is VOL. The status returns to the standby status after RDY/Busy returns to High-Z. By using program (4), data can be rewritten for each sector. This interval can be repeated (h - 1) cycle.(1 h 2048 + 64) High-Z*4 SA(1) SA(2) CA(1) CA(2) PD(n) PD(n+1) PD(n+i)*1 CA(1)' CA(2)' PD(m) PD(m+1)PD(m+j)*2 40H I/O7=VOL I/O7=VOH t tDHAS tAH tAS tAH tAS tAH tAS tCDH tWSD tCDH tSCC tSPL tSP *1 tSP tCDSH tAH tCDH tAH tSDS tSCC tSPL tSDH *2 tSP tSP tDS tWP tWP tWP tCDSS tCDS tWP tWP tCDSS tWP tSW tCDH tSCHW tDH tDF tDF tASP tCDS tCWC tWPH tCEH tCE
tOEPS
tOE
tRDY
WE
tAH t tSDS SDH
tAS
tAS
Program (4) with CA after SC and Status Data Polling Timing Waveform
h cycle*6 CE tCES OE tOEWS tCWC tCWC tWPH tWPH tSW tCDS tWP tCDS tWP CDE tSCS SC tDS I/O0 to I/O7 11H RES tRP RDY /Busy Notes: 1. 2. 3. 4. 5. 6. tDBR SA(1) SA(2) PD0 PD1 PD(k)*1 CA(1) CA(2) PD(m) PD(m+1)PD(m+j)*2 40H I/O7=VOL I/O7=VOH t tDHAS tAH tAS tAH tSDS tCDH tCDH tWSD tSCC tSPL tSDH tSP *1 tSP tCDSH tAH tCDH tAH tSCC tSPL tSDH *2 tSP tSP tWP tCDSS tCDS tWP tWP tCDSS tWP tSW tCDH tSCHW tDH tDF tDF tASP tCDS tCWC tWPH tCEH tCE
tOEPS
tOE
tRDY
WE
tAS
tAS
tSDS
tDS
tRBSY tRS High-Z tDB *3 The programming operation is not guaranteed when the number of the SC pulse exceeds 2112.(0 k 2111) The programming operation is not guaranteed when the number of the SC pulse exceeds (2112 - m).(j 2111 - m, 0 m 2111) Any commands, including reset command FFH, cannot be input while RDY/Busy is VOL. The status returns to the standby status after RDY/Busy returns to High-Z. By using program (4), data can be rewritten for each sector. This interval can be repeated h cycle.(1 h 2048 + 64) High-Z*4
31
HN29W12811 Series
ID and Status Register Read Timing Waveform
*1 CE tCES OE tOEWS WE tCDS CDE tSCHW SC tSCS I/O0 to I/O7 90H RES tRP RDY /Busy Note: 1. The status returns to the standby at the rising edge of CE. High-Z Manufacturer Device Manufacturer code code code Status register tDS tDH t OE tCDF tCDAC tCDF tCDAC tDF tSCS tOE tDF tCE tWP tCDH tCDCH tOEPS tCOH tCOH *1
32
HN29W12811 Series
Data Recovery Read Timing Waveform
*1 tCPH tCES OE tOEWS WE tCDS CDE tWSDR SC tSCS I/O0 to I/O7 01H RES High-Z RDY /Busy Notes: 1. The status returns to the standby at the rising edge of CE. 2. Output data is not valid after the number of the SC pulse exceed 2112 in the recovery data read mode. 3. After any commands are written, the status can turns to the standby after the command FFH is input and CE turns to the VIH level. D0out D1out D2111out High *2 FFH tDS tDH tWP tCDH tOES tSCC tSP tOEL tSAC tSCC *2 tSOH tCDS tOER tCDOS tWP tCDH tCWHR tCOH *3
CE
tCEH
tSPL
t t tSH SAC tSH SAC
tSAC
tDF tDS
tDH
33
HN29W12811 Series
Data Recovery Write Timing Waveform
CE tCES OE tOEWS WE tCDS CDE tWP tCDS tCDH SC tSCS I/O0 to I/O7 12H RES High-Z RDY /Busy tDB *1 *2 High-Z SA(1) High SA(2) 40H IO7 = VOL IO7 = VOH tDS tDH tAS tAH tAS tAH tDS tDH tDF tDF tWP tWP tWP tCDS tCDH tCDH tSCHW tASP tCWC tWPH tCWC tWPH tCWC tWPH tCEH tOEPS tCE tOE tCOS
tRDY tCDS
Notes: 1. Any commands,including reset command FFH, cannot be input while RDY/Busy is VOL. 2. The status returns to the standby status after RDY/Busy returns to High-Z.
34
HN29W12811 Series
Clear Status Register Timing Waveform
*1 CE tCES OE tOEWS WE tWP tCDH CDE tCDS SC tSCS tDS tDH tDS tDH tSCS tDS tDH tWWH tCDS tWP tCDH tCPH tCES
tCWH
tOEWS tCDS tWP tCDH
I/O0 to I/O7 50H RES High High-Z Next Command Next Command
RDY /Busy
Note 1. The status returns to the standby at the rising edge of CE.
35
HN29W12811 Series
Function Description
Status Register: The HN29W12811 outputs the operation status data as follows: I/O7 pin outputs a V OL to indicate that the memory is in either erase or program operation. The level of I/O7 pin turns to a VOH when the operation finishes. I/O5 and I/O4 pins output V OLs to indicate that the erase and program operations complete in a finite time, respectively. If these pins output VOHs, it indicates that these operations have timed out. When these pins monitor, I/O7 pin must turn to a VOH . To execute other erase and program operation, the status data must be cleared after a time out occurs. From I/O0 to I/O3 pins are reserved for future use. The pins output VOLs and should be masked out during the status data read mode. The function of the status register is summarized in the following table.
I/O I/O7 I/O6 I/O5 I/O4 I/O3 I/O2 I/O1 I/O0 Flag definition Ready/Busy Reserved Erase check Program check Reserved Reserved Reserved Reserved Definition VOH = Ready, VOL = Busy Outputs a V OL and should be masked out during the status data poling mode. VOH = Fail, VOL = Pass VOH = Fail, VOL = Pass Outputs a V OL and should be masked out during the status data poling mode.
Requirement for System
Specifications
Item Usable sectors (initially) Spare sectors ECC (Error Correction Code) Program/Erase endurance Min 8,029 145 1 -- Typ -- -- -- -- Max 8,192 -- -- 3 x 10
5
Unit sector sector bit/sector cycle
36
HN29W12811 Series
Unusable Sector Initially, the HN29W12811 includes unusable sectors. The unusable sectors must be distinguished from the usable sectors by the system as follows. 1. Check the partial invalid sectors in the devices on the system. The usable sectors were programmed the following data. Refer to the flowchart "The Unusable Sector Indication Flow". Initial Data of Usable Sectors
Column address Data 0H to 81FH FFH 820H 1CH 821H 71H 822H C7H 823H 1CH 824H 71H 825H C7H 826H to 83FH FFH
2. Do not erase and program to the partial invalid sectors by the system.
START
Sector number = 0
Read data
Column address = 820H to 825H
Sector number = Sector number + 1
Bad sector*2
No
Check data*1 Yes
No
Sector number = 8,191 Yes
END Notes: 1. Refer to table "Initial data of usable sectors". 2. Bad sectors are installed in system.
The Unusable Sector Indication Flow
37
HN29W12811 Series
Requirements for High System Reliability The device may fail during a program, erase or read operation due to write or erase cycles. The following architecture will enable high system reliability if a failure occurs. 1. For an error in read operation: An error correction more than 1-bit error correction per each sector read is required for data reliability. 2. For errors in program or erase operations: The device may fail during a program or erase operation due to write or erase cycles. The status register indicates if the erase and program operation complete in a finite time. When an error occurred in the sector, try to reprogram the data into another sector. Avoid further system access to the sector that error happens. Typically, recommended number of a spare sectors are 1.8% of initial usable 8,029 sectors by each device. If the number of failed sectors exceeds the number of the spare sectors, usable data area in the device decreases. For the reprogramming, do not use the data from the failed sectors, because the data from the failed sectors are not fixed. So the reprogram data must be the data reloaded from external buffer, or use the Data recovery read mode or the Data recovery write mode (see the "Mode Description" and under figure "Spare Sector Replacement Flow after Program Error"). To avoid consecutive sector failures, choose addresses of spare sectors as far as possible from the failed sectors.
38
HN29W12811 Series
START
Program start
Set an usable sector
Program end
Check RDY/Busy
Check status Yes
No
Clear status register
Load data from external buffer
Data recovery read
Data recovery write
Program start
Set another usable sector
Program end
Check RDY/Busy
Check status Yes Check status: Status register read END
No
Spare Sector Replacement Flow after Program Error
39
HN29W12811 Series
Memory Structure
bit
8,192 sectors
sector
byte (8 bits)
2,112 bytes (16,896 bits)
Bit: Minimum unit of data. Byte: Input/output data unit in programming and reading. (1 byte = 8 bits) Sector: Page unit in erase, programming and reading. (1 sector = 2,112 bytes = 16,896 bits) Device: 1 device = 8,192 sectors.
40
HN29W12811 Series
Package Dimensions
HN29W12811T Series (TFP-48DA)
Unit: mm
25
12.00 12.40 Max 48
1 0.50 *0.22 0.08 0.08 M 0.20 0.06 0.45 Max 1.20 Max
24 *0.17 0.05 0.125 0.04
18.40
0.80 20.00 0.20 0 - 5 0.05 0.05 0.50 0.10
Hitachi Code JEDEC EIAJ Mass (reference value) TFP-48DA Conforms Conforms 0.49 g
0.10
*Dimension including the plating thickness Base material dimension
41
HN29W12811 Series
Cautions
1. Hitachi neither warrants nor grants licenses of any rights of Hitachi's or any third party's patent, copyright, trademark, or other intellectual property rights for information contained in this document. Hitachi bears no responsibility for problems that may arise with third party's rights, including intellectual property rights, in connection with use of the information contained in this document. 2. Products and product specifications may be subject to change without notice. Confirm that you have received the latest product standards or specifications before final design, purchase or use. 3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However, contact Hitachi's sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment or medical equipment for life support. 4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly for maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as fail-safes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other consequential damage due to operation of the Hitachi product. 5. This product is not designed to be radiation resistant. 6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without written approval from Hitachi. 7. Contact Hitachi's sales office for any questions regarding this document or Hitachi semiconductor products.
Hitachi, Ltd.
Semiconductor & Integrated Circuits. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109
URL
NorthAmerica Europe Asia Japan
: : : :
http://semiconductor.hitachi.com/ http://www.hitachi-eu.com/hel/ecg http://sicapac.hitachi-asia.com http://www.hitachi.co.jp/Sicd/indx.htm
Hitachi Asia Ltd. Hitachi Tower 16 Collyer Quay #20-00, Singapore 049318 Tel : <65>-538-6533/538-8577 Fax : <65>-538-6933/538-3877 URL : http://www.hitachi.com.sg Hitachi Asia Ltd. (Taipei Branch Office) 4/F, No. 167, Tun Hwa North Road, Hung-Kuo Building, Taipei (105), Taiwan Tel : <886>-(2)-2718-3666 Fax : <886>-(2)-2718-8180 Telex : 23222 HAS-TP URL : http://www.hitachi.com.tw Hitachi Asia (Hong Kong) Ltd. Group III (Electronic Components) 7/F., North Tower, World Finance Centre, Harbour City, Canton Road Tsim Sha Tsui, Kowloon, Hong Kong Tel : <852>-(2)-735-9218 Fax : <852>-(2)-730-0281 URL : http://www.hitachi.com.hk
For further information write to:
Hitachi Semiconductor (America) Inc. 179 East Tasman Drive, San Jose,CA 95134 Tel: <1> (408) 433-1990 Fax: <1>(408) 433-0223 Hitachi Europe GmbH Electronic Components Group Dornacher Strae 3 D-85622 Feldkirchen, Munich Germany Tel: <49> (89) 9 9180-0 Fax: <49> (89) 9 29 30 00 Hitachi Europe Ltd. Electronic Components Group. Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA, United Kingdom Tel: <44> (1628) 585000 Fax: <44> (1628) 585160
Copyright (c) Hitachi, Ltd., 2000. All rights reserved. Printed in Japan.
Colophon 2.0
42

▲Up To Search▲

Price & Availability of HN29W12811

	To Download HN29W12811 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .